Design and Evaluate A Model of Vehicle Suspension System by Using Fem
DOI:
https://doi.org/10.24113/ijoscience.v5i10.231Keywords:
FEA, ANYSIS, CATIA, Aluminum, cast iron, Titanium.Abstract
The suspension system assists the vehicle's braking system in terms of safety, driving pleasure and passenger comfort when driving without road noise, bumps or vibrations. If the roads were perfectly smooth, a vehicle suspension system would not be necessary. As a result, the wheel of the machine undergoes a sudden vertical movement as it moves over the bumps. To improve the stability of the suspension system design multiple spring in vehicle suspension system and the design multiple spring in vehicle suspension system for different materials to enhance the results. Final conclusion of the analysis the Titanium Ti-6Al-4V is the much batter material than other two materials Cast iron and titanium Ti-13V-11Cr-3Al. Because the yield stress of Titanium Ti-6Al-4V is higher the titanium Ti-13V-11Cr-3Al. And the density of the Titanium Ti-6Al-4V was lower than cast iron and titanium Ti-13V-11Cr-3Al.
Downloads
References
[2] B. Pyttel, I. Brunnera “Fatigue behavior of helical compression springs at a very high number of cycles – Investigation of various influences” DOI: 10.1016/j.ijfatigue.2013.01.003 March 2014.
[3] Yunan Prawoto, M. Ikeda “Design and failure modes of automotive suspension springs” DOI: 10.1016/j.engfailanal.2007.11.003 15(8):1155-1174 · December 2008.?
[4] Ladislav Kosec, Aleš Nagode “Failure analysis of a motor-car coil spring” DOI: 10.1016/j.csefa.2013.12.004 4(C) · December 2013.
[5] Senthilkumar Mouleeswaran, S. Vijayarangan “Analytical and experimental studies on fatigue life prediction of steel and composite leaf spring for light passenger vehicles using life data analysis” Vol.13(No.2):pp.141-146 · June 2007.
[6] Bankole I. Oladapo, C.O. Ijagbemi “Design and Simulation of Fatigue Analysis for a Vehicle Suspension System (VSS) and its Effect on Global Warming” 10.1016/j.proeng.2016.08.135 .
[7] Izatul Hamimi Abdul Razak “Modeling, Simulation And Optimization Analysis Of Steering Knuckle Component For Race Car” DOI: 10.15623/ijret.2014.0311037 November 2014.
[8] Hari Dayalan, Yeshwant Raj.s “Investigation of Knuckle Joint and Its Importance -A Literature Case Study” January 2018.
[9] Gaurav Saxena, Ankit Chauhan “Simulation and Optimization of wheel Hub and Upright of Vehicle: A Review” DOI: 10.9790/1684-1401034250 January 2017.
[10] Vi Kie Soo, Paul Compston, Paul Compston “Interaction between New Car Design and Recycling Impact on Life Cycle Assessment” DOI: 10.1016/j.procir.2015.02.055 December 2015.
Downloads
Published
Issue
Section
License
Copyright (c) 2019 Vikesh Kumar Ranjan, Arun Patel
This work is licensed under a Creative Commons Attribution 4.0 International License.
IJOSCIENCE follows an Open Journal Access policy. Authors retain the copyright of the original work and grant the rights of publication to the publisher with the work simultaneously licensed under a Creative Commons CC BY License that allows others to distribute, remix, adapt, and build upon your work, even commercially, as long as they credit you for the original creation. Authors are permitted to post their work in institutional repositories, social media or other platforms.
Under the following terms:
-
Attribution — You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
- No additional restrictions — You may not apply legal terms or technological measures that legally restrict others from doing anything the license permits.
